Please enter some search terms and try again.

NF9W-2930 Baytrail - Mini-ITX Intel Baytrail Motherboard

Product image
Datasheet

Product Features

 

- Intel Celeron N2930 SoC Processor
- Embedded Class Planned Lifecycle through Q1.2019
- Ultra Slim Design with 20mm z-height and Low Profile IO Shield
- 1 * External RS232/422/485 Serial Port & 1 * Internal Serial Header
- 12V DC-in or Alternate Internal 2-pin Power Connector
- ECO-design for EuP/ErP

 

Specification

 

Jetway NF9W Mini-ITX Motherboard
Processor Intel® Celeron N2930 SoC, 1.83GHz – 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP
Memory 1 x 204-pin DDR3L-1333 SO-DIMM up to 8GB (1.35V required)
Graphics Intel HD Graphics, 313MHz - 854MHz
Audio Realtek ALC662 2.1 Channel HD Audio with 3W Amplifier
LAN 1 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
Storage 2 x SATA3 6Gb/s Connector
2 x SATA2 3Gb/s Connector
Super IO FINTEK F81768D-I
Back Panel Connectors
1 12V DC-In jack
1 USB 3.0
3 USB 2.0
1 DVI-I
1 Serial port (RS232/422/485)
1 RJ45 LAN (10/100/1000)
1 3.5mm Line-out jack
Onboard I/O Connectors
1 PCI Express x1 Slot
1 Full size mini PCI-E Slot
2 SATA3 6Gb/s Connectors
2 SATA2 3Gb/s Connectors
3 USB Pin Headers for up to 5 additional USB 2.0 Ports
1 RS232 Serial Port Header
1 24-bits Dual Channel LVDS connector/Inverter
1 AT/ATX power switch mode select jumper
1 Chassis Intrusion Header
1 5-pin SMBUS(I2C) Header
1 8-bit GPIO Header
1 9-pin Audio Header
1 2-pin LAN LED Header
1 9-pin Front Panel Header
1 4-pin Speaker Header
3 4-pin Fan Headers
1 2-pin SPDIF Out Header
1 2-pin MON_PWR Out Connector
2 4-pin SATA Power Out Connector (Male)
1 2-pin +12V Alternate Power Connector (Molex 5566-2)
Power Supply for NF9W
External Power Supply – the board can be powered with a 12V external power supply though a DC connector on the back panel. The rear 12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 12V and the shell is GND.

Internal Power Supply – the board can alternatively be powered via the internal 12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 (±10%) VDC. The internal 1 x 2 power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.

Caution: There is no isolation circuitry between the external 12V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12V DC jack is covered if the internal 1 x 2 power connector is to be used.
Environment
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C

See also 


Please contact us for volume pricing.


We like to make life easier, for further help and assistance with this product click to our FAQ's page.

Want more help to find a solution? Contact us or check out our design capabilities.